• MEGR 6120 Commercial Regulator Specs PDF

**To maximize the lifespan of the regulator, it must be installed above the liquid level of propane: directly connect to service valve, or wall mount above the propane cylinder(s).

Features/Specifications:

• Type: Adjustable or Fixed / PSI
• Max. Inlet Pressure: 250 PSIG (17,2 bar)
• Inlet Connection: 1/4” FNPT
• Outlet Connections: 1/4” FNPT
• Gauge Port: 1/4” FNPT
• Exterior Finish: Red Wet Coat
• Diaphragm: Fabric Reinforced Buna N
• Body/ Bonnet Material: Die Cast Aluminum
• Liquid Capacity: 3-5 GPH
• Listings: UL LISTED / UL 144

The MEGR-6120 Series are UL LISTED high-pressure regulators that meet a variety of applications for liquid or vapor
service. The compact body design makes these regulators particularly useful in installations with space limitations. The basic
MEGR-6120 Series regulators come equipped with a handwheel adjustment. The non-adjustable ME6121 Series provides a
tamper-resistant spring case and one of seven fixed setpoints: 5, 10, 20, 30, 40, 50, or 60 PSI.
The MEGR-6120 & MEGR-6121 Series are UL listed as high pressure, non-relief regulators. Both MEGR-6120 & MEGR-6121 Series
regulators contain brass materials that are not compatible with anhydrous ammonia service.

• MEGR 164 222 Commercial Regulator Specs PDF

**To maximize the lifespan of the regulator, it must be installed above the liquid level of propane: directly connect to service valve, or wall mount above the propane cylinder(s).

Features/Specifications:

• Type: Adjustable/PSI
• Max. Inlet Pressure: 250 PSI
• Inlet Connection: 1/2” FNPT or 3/4” FNPT
• Outlet Connection: 1/2” FNPT or 3/4” FNPT
• Exterior Finish:Gray Urethane
• Regulator Spring: Steel
• Stem Guide/Disk Holder: Stainless Steel
• Diaphragm: Fabric Rienforced Nitrile (NBR)
• Bonnet / Body Material: Cast Aluminum
• Vent: Non-Relieving

The MEGR-164 Series adjustable high-pressure regulators offer a wide selection of available pressure ranges. High pressure regulators are typically used to reduce tank pressure to an intermediate pressure for use by another regulator. They may be used as high pressure regulators on distribution systems when used in conjunction with first-stage down stream regulators. When equipped with an integral relief valve (MEGR-164SR
Series), the regulator may be used as a final-stage regulator on high pressure systems. It may also be used as a first-stage regulator when set at 10 PSIG (0,69 bar) or less. The 1/4”-inch FNPT tapped side outlet can be used to install a pressure gauge or a hydrostatic relief valve. This series contains brass materials that are not compaƟ ble with anhydrous ammonia service.

Marshall Excelsior 2PSI Regulators Spec PDF

**To maximize the lifespan of the regulator, it must be installed above the liquid level of propane: directly connect to service valve, or wall mount above the propane cylinder(s).

Features/Specifications:

• Type: Integral Two-Stage 2 PSI
• Max. Inlet Pressure: 250 PSIG
• Exterior Finish: White Powder Coat
• Orifice Size: .17” (Compact) & 7/32” (Full)
• Seat Material: Fluorocarbon (FKM)
• Diaphragm: Fabric Reinforced NBR/Molded Lip O-Ring Bonnet/Body Seal
• Relief Type: Internal Relief – Spring Loaded
• Bonnet / Body Material: Die Cast Aluminum
• Listings: C ULUS / UL 144
• Mounting Holes: Standard 3-1/2” Center
• Pressure Taps: #54 Orifi ce 1/8” FNPT Plugged (3)
• Relief Travel Stop: Molded in Adjustment Cap –
  Gray (Compact), Black (Full Size)

MEC Excela-Flo integral two-stage regulators combine the first and second stage regulator set-up into one convenient unit converting tank pressure to 2 PSI. All MEC integral two-stage 2 PSI regulators are white indicating 2 PSI outlet pressure. Integral two-stage 2 PSI regulators are recommended for installations with short piping distances, but provide the same advantages of two-stage regulation with a single unit. 2 PSI service regulators are used in conjunction with an LPG line regulator either at the indoor appliance or a remote manifold distribution header inlet. All MEC integral two-stage regulator vent have tapped ports (7/16 -24 – First Stage) (3/8” FNPT or 3/4” FNPT – Second Stage) and our exclusive E-Z Grip screens located over the outlet. Both the MEGR-1232E and MEGR1632E series offer optimal relief performance that well exceeds UL test requirements providing over pressure protection of no more than 4 PSI downstream pressure. MEC Excela-Flo integral two-stage domesƟ c regulators feature a 25 year recommended replacement life, our exclusive Tri-TapTM (tank, 10 PSI, 2 PSI) pressure port system and tear away leak check adhesive sticker.

• MEGR-1222, MEGR-1252, MEGR-1622 & MEGR-1652

Marshall Excelsior Second Stage Regulator Specs PDF

Features/Specifications:

• Type: Second Stage
• Max. Inlet Pressure: 10 PSIG
• Exterior Finish: Green Powder Coat
• Interior Finish: Green Powder Coat
• Orifice Size: .14” (Compact) & 7/32” (Full)
• Diaphragm: Fabric Reinforced (NBR) Molded Lip O-Ring Bonnet/Body Seal
• Relief Type: Internal Relief – Spring Loaded
• Bonnet / Body Material: Die Cast Aluminum
• Seat Material: Fluorocarbon (FKM)
• Listings: C US / UL 144
• Mounting Holes: Standard 3-1/2” Center
• Pressure Taps: #54 Orifi ce 1/8” FNPT Plugged (2)
• Relief Travel Stop: Molded In Adjustment Cap –
  Black (Full Size), Gray (Compact)

• MEGR-1122H – Compact Series
• MEGR-1622H – Full Size Series

Marshall Excelsior First Stage Regulators Specs

**To maximize the lifespan of the regulator, it must be installed above the liquid level of propane: directly connect to service valve, or wall mount above the propane cylinder(s).

• No stock #

Features/Specifications:

• Type: First Stage
• Max. Inlet Pressure: 250 PSIG
• Exterior Finish: Red Powder Coat
• Interior Finish: Red Powder Coat
• Orifice Size: .15” (Compact) & 7/32” Full
• Diaphragm: Fabric Reinforced NBR Molded Lip O-Ring Bonnet/Body Seal
• Relief Type: Internal Relief – Spring Loaded
• Bonnet / Body Material: Die Cast Aluminum
• Seat Material: Fluorocarbon (FKM)
• Listings: C US / UL 144
• Mounting Holes: Standard 3-1/2” Center
• Pressure Taps: #54 Orifi ce 1/8” FNPT Plugged (2)
• Relief Travel Stop: Molded in Adjustment Cap –

**To maximize the lifespan of the regulator, it must be installed above the liquid level of propane: directly connect to service valve, or wall mount above the propane cylinder(s).

• MEGR350-10: 0-10 PSI adjustable – #3802
• MEGR350-20: 1.2Million BTU capacity, 0-20PSI adjustable – #3433
• MEGR350-30: 1.2Million BTU capacity, 0-30 PSI adjustable – #4698

The MEGR-350 is a single stage, adjustable high pressure regulator. The body and bonnet of both the fixed and adjustable regulators
are precisely machined and feature a crimped design and fabric reinforced rubber diaphragm creating a positive seal for leak-free
performance.

Features/Specifications:

• Type: Fixed / PSI
• Max. Inlet Pressure: 250 PSIG (17,2 bar)
• Inlet Connection: 1/4” FNPT
• Outlet Connections: 1/4” FNPT
• Orifice Diameter: 0.0625”
• Exterior Finish: Red Anodized
• Diaphragm: Fabric Reinforced Buna N
• Body/ Bonnet Material: Die Cast Zinc
• BTU/H Capacity: 1,200,000 BTU/H @ 40 PSI
• Listings: UL LISTED / UL 144

Marshall Excelsior MEGR-130 and MEGR-350 Series Brochure

**To maximize the lifespan of the regulator, it must be installed above the liquid level of propane: directly connect to service valve, or wall mount above the propane cylinder(s).

• MEGR130-10: Preset 10PSI outlet – #3683
• MEGR130-20: 600,000 BTU capacity – Preset 20PSI outlet – #3737
• MEGR130-30: 1.2Million BTU capacity – Preset 30PSI outlet – #3692

The MEGR-130 series fixed high pressure single stage regulators are designed to provide an economical solution for pounds to pounds service applications. The MEGR-130 can be used to regulate air as well as LP gas. Regulators must be installed in compliance with federal, state or local codes or laws in accordance with NFPA 58.

Features/Specifications:

• Type: Fixed / PSI
• Max. Inlet Pressure: 250 PSIG (17,2 bar)
• Inlet Connection: 1/4” FNPT
• Outlet Connections: 1/4” FNPT
• Orifice Diameter: 0.0625”
• Exterior Finish: Red Anodized
• Diaphragm: Fabric Reinforced Buna N
• Body/ Bonnet Material: Die Cast Zinc
• BTU/H Capacity: 1,200,000 BTU/H @ 40 PSI
• Listings: UL LISTED / UL 144

Marshall Excelsior MEGR-130 and MEGR-350 Series Brochure

**To maximize the lifespan of the regulator, it must be installed above the liquid level of propane: directly connect to service valve, or wall mount above the propane cylinder(s).

• MEGR-6121-05 – Preset at 5PSI output – #4800
• MEGR-6121-10 – Preset at 10PSI output – #4801
• MEGR-6121-20 – Preset at 20PSI output – #4353
• MEGR-6121-30 – Preset at 30PSI output – #4802

Features/Specifications:

• Type: Fixed / PSI
• Max. Inlet Pressure: 250 PSIG (17,2 bar)
• Inlet Connection: 1/4” FNPT
• Outlet Connections: 1/4” FNPT
• Gauge Port: 1/4” FNPT
• Exterior Finish: Red Wet Coat
• Diaphragm: Fabric Reinforced Buna N
• Body/ Bonnet Material: Die Cast Aluminum
• Liquid Capacity: 3-5 GPH
• Listings: UL LISTED / UL 144

Marshall Excelsior MEGR-6120 MEGR-6121 Series Brochure